View TB6612FNG_9086322.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TB6612FNG toshiba bi - cd integrated circuit silicon monolithic tb6 612 fng driver ic for dual dc motor TB6612FNG is a driver ic for dc motor with output transistor in ld mos structure with low on - resistor. two input signals, in1 and in2, can choose one of four modes such as cw, ccw, short brake, and stop mode. features ? power supply voltage : v m = 15 v ( max ) ? output current : i out = 1.2 a(ave) / 3. 2 a (peak) ? output low on resistor : 0.5 ( upper + lower typ. @ v m 5 v) ? standby (power save) system ? cw / ccw / short brake / stop function modes ? built - in thermal shutdown circuit and low voltage detecting circuit ? small faced package ( ssop24 : 0.65 mm lead pitch ) * this product has a mos struc ture and is sensitive to electrostatic discharge. when handling this product, ensure that the environment is protected against electrostatic discharge by using an earth strap, a conductive mat and an ionizer . ensure also that the ambient temperature and re lative humidity are maintained at reasonable levels. weight : 0.14 g ( typ. ) ? 201 4 toshiba corporation 201 4 - 1 0 - 01 1
TB6612FNG block diagram pin functions n o . pin name i/o function 1 ao1 o ch a output 1 2 ao1 3 pgnd1 D power gnd 1 4 pgnd1 5 ao2 o ch a output 2 6 ao2 7 bo2 o ch b output 2 8 bo2 9 pgnd2 D power gnd 2 10 pgnd2 11 bo1 o ch b output 1 12 bo1 13 vm2 D motor supply 14 vm 3 15 pwmb i ch b pwm input / 200 k D D D
TB6612FNG absolute maximum ratings (ta = 25c) operating range ( ta = - 20 to 85c ) characteristics symbol rating unit remarks supply voltage vm 15 v v cc 6 inp ut voltage v in - 0.2 to 6 v in1,in2,stby,pwm pins output voltage v out 15 v o1,o2 pins output current i out 1.2 a per 1 ch i out (peak) 2 tw = 20 ms continuous pulse, duty 20% 3.2 tw = 10 ms single pulse power dissipation p d 0.78 w ic only 0.89 50 mm 50 mm t = 1.6 mm cu 30% in pcb mo u nting operating temperature t opr - 20 to 85 c storage temperature t stg - 55 to 150 c characteristics s ymbol min typ. max unit remarks supply voltage v cc 2.7 3 5.5 v vm 2.5 5 13.5 v output current (h - sw) i out D D D D 0.4 4.5 v > vm 2.5 v without pwm operation switching frequency f pwm D D ; in1,in2,pwm,stby vcc g nd i nput i nternal circuit 2 00k ; o1,o2 vm pg nd o1 o2 input pin : out put pin : o1, o2 o1 o2 v m 201 4 - 1 0 - 01 3
TB6612FNG h - sw control function input output in1 in2 pwm stby out1 out2 mode h h h/l h l l short brake l h h h l h ccw l h l l short brake h l h h h l cw l h l l short brake l l h h off (high impedance) stop h/l h/l h/l l off (hig h impedance) standby h - sw operating description ? to prevent penetrating current, dead time t2 and t4 is provided in switching to each mode in the ic. v m v m v m m v m gnd t5 m v m gnd t4 m gnd m gnd t3 m gnd t2 t1 out2 out1 out1 out1 out1 out1 out2 out2 out2 out2 gnd v m out1 voltage wave t1 t2 t3 t5 t4 201 4 - 1 0 - 01 4
TB6612FNG electrical characteristics ( unless otherwise specified, ta = 25c, v cc = 3 v , v m = 5 v ) characteristics symbol test condition min typ. max unit supply current i cc (3 v ) stby = v cc = 3 v, vm = 5 v D D D D a i m(stb) D D D vcc 0.7 D D a i il v in = 0 v D D D vcc 0.7 D D a i il(stb) v in = 0 v D D D 0.5 0.7 v v sat(u+l)2 i o = 0.3 a, vcc = vm = 5 v D D D a i l(l) vm = 15 v, v out = 0 v - 1 D D D D D 1.9 D v recove ring voltage uvlc D D D 24 D ns t f D D D D D D D 175 D c thermal shutdown hysteresis ? tsd D 20 D 201 4 - 1 0 - 01 5
TB6612FNG target characteristics pd - ta 0.00 0.50 1.00 1.50 0 50 100 150 ta () (w) icgj-a=160/w ?g?r pcbe 50501.6mm cueR40% ?g?r pcbe 76.2114.31.6mm cueR30% ic only j ? a = 160 c /w in boarding pcb area 50 mm50 mm1.6 mm cu area 40% power dissipation p d p d - ta ta = 25c , ic only 1 ch driving 2 ch drivi ng iout - duty 0.0 0.5 1.0 1.5 2.0 2.5 0% 20% 40% 60% 80% 100% duty (a) 2chr 1chr ta=25,icg output current i out i out - duty dual - channel operation single - channel operation ta = 25 c, ic only 201 4 - 1 0 - 01 6
TB6612FNG typical application diagram note: condensers for noise absorption (c1, c2, c3, and c4) should b e connected as close as possible to the ic. +4.5v 13.5v + c1 10uf c2 0.1uf m mcu s tby a i n1 ain2 pwma h-sw driver a 18 t sd vcc g nd 2 ao1 24 vm1 control logic a 20 21 22 23 19 3 p g nd1 b i n1 bin2 pwmb control logic b 17 16 15 stby uvlo 4 p g nd1 1 ao1 6 ao2 5 ao2 h-sw driver b 11 bo1 13 vm2 9 p g nd2 10 p g nd2 12 bo1 7 bo2 8 bo2 14 vm3 m +2.7v 5.5v + c3 10uf c4 0.1uf +2.7 v to 5.5 v + 4.5 v to 13. 5 v 201 4 - 1 0 - 01 7
TB6612FNG package dimennsions weght : 0.14 g ( typ ) detail of a terminal 201 4 - 1 0 - 01 8
TB6612FNG notes on contents 1. block diagrams some of the functional blocks, circuits, or constan ts in the block diagram may be omitted or simplified for explanatory purposes. 2. equivalent circuits the equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory purposes. 3. timing charts timing charts may be simplified for explanatory purposes. 4. application circuits the application circuits shown in this document are provided for reference purposes only. thorough evaluation is required, especially at the mass production design stage. toshiba does not grant any license to any industrial property rights by providing these examples of application circuits. 5. test circuits components in the test circuits are used only to obtain and confirm the device characteristics. these components and circuits are not guar anteed to prevent malfunction or failure from occurring in the application equipment. ic usage considerations notes on handling of ics [1 ] the absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a m oment. do not exceed any of these ratings. exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. [ 2 ] use an appropriate power supply fuse to ensure that a large current does not continuously flow in case of over current and/or ic failure. the ic will fully break down when used under conditions that exceed its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise occurs from the wiring or lo ad, causing a large current to continuously flow and the breakdown can lead smoke or ignition. to minimize the effects of the flow of a large current in case of breakdown, appropriate settings, such as fuse capacity, fusing time and insertion circuit locat ion, are required. [ 3 ] if your design includes an inductive load such as a motor coil, incorporate a protection circuit into the design to prevent device malfunction or breakdown caused by the current resulting from the inrush current at power on or the negative current resulting from the back electromotive force at power off. ic breakdown may cause injury, smoke or ignition. use a stable power supply with ics with built - in protection functions. if the power supply is unstable, the protection function ma y not operate, causing ic breakdown. ic breakdown may cause injury, smoke or ignition. [4] do not insert devices in the wrong orientation or incorrectly. make sure that the positive and negative terminals of power supplies are connected properly. otherwi se, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. in addition, do not use any device that is a pplied the current with inserting in the wrong orientation or incorrectly even just one time. 201 4 - 1 0 - 01 9
TB6612FNG points to remember on handling of ics ( 1 ) thermal shutdown circuit thermal shutdown circuits do not necessarily protect ics under all circumstances. if the the rmal shutdown circuits operate against the over temperature, clear the heat generation status immediately. depending on the method of use and usage conditions, such as exceeding absolute maximum ratings can cause the thermal shutdown circuit to not operate properly or ic breakdown before operation. ( 2 ) heat radiation design in using an ic with large current flow such as power amp, regulator or driver, please design the device so that heat is appropriately radiated, not to exceed the specified junction temp erature (t j ) at any time and condition. these ics generate heat even during normal use. an inadequate ic heat radiation design can lead to decrease in ic life, deterioration of ic characteristics or ic breakdown. in addition, please design the device takin g into considerate the effect of ic heat radiation with peripheral components. (3) back - emf when a motor rotates in the reverse direction, stops or slows down abruptly , a current flow back to the motor s power supply due to the effect of back - emf. if the current sink capability of the power supply is small, the device s motor power supply and output pins might be exposed to conditions beyond absolute maximum ratings. to avoid this problem, take the effect of back - emf into consideration in system design. 201 4 - 1 0 - 01 10
TB6612FNG restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collectively "toshiba"), reserve the right to make changes to the i nformation in this document, and related hardware, software and systems (collectively "product") w ithout notice. ? this document and any information herein may not be reproduced without prior written permission from toshiba. even with toshiba's written permission, reproduction is permissible only if reproduction is without alteration/omission. ? though toshiba works continually to improve product's quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, softwar e and syste ms which minimize risk and avoid situations in which a malfunction or failure of product could cause loss of human life, bodi ly injury or damage to property, including data loss or corruption. before customers use the product, create designs including t he product, or incorporate the product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant toshiba information, including without limitation, this document, the specifications, the data sheets and application notes for product and the precautions and conditions set forth in the "toshiba semiconductor reliability handbook" and (b) the instructions for the application with which the product will be used with or for. customers are solely responsible fo r all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this produ ct in such design or applications; (b) evaluating and determining the applicability of any information conta ined in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operat ing parameters for such designs and applications. toshiba assumes no liability for customers' product design or applications. ? product is neither intended nor warranted for use in equipments or systems that require extraordinarily high levels of quality and/or reliability, and/or a malfunction or failure of which may cause loss of human life, bodi ly injury, serious property damage and/or serious public impact ( " unintended use " ). except for specific applications as expressly stated in this document, unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance - related fields. if you use product for unintended use, toshiba assumes no liability for product. for details, please contact your toshiba sales representative. ? do not disassemble, analyze, reverse - engineer, alter, modify, translate or copy product, whether in whole or in part. ? product s hall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is presented only as guidance for product use. no responsibility is assumed by toshiba for any infringement of patents or any other intellectual property rights of third parties that may result from the use of product. n o license to any intellectual property right is granted by this document, whether express or implied, b y estoppel or otherwise. ? absent a written signed agreement, except as provided in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation , indirect, consequential, special, or incidental damages or loss, including without limitation, loss of profits, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions rela ted to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? do not use or otherwise make available product or related software or techn ology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or mis sile technology products (mass destruction weapons). product and related softwar e and technology may be controlled under the applicable export laws and regulations including, without limitation, the japanese foreign exchange and foreign trade law and the u.s. export administration regulations. export and re - export of product or relate d software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pr oduct. ple ase use product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled subst ances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losse s occurring as a resul t of noncompliance w ith applicable laws and regulations. 201 4 - 1 0 - 01 11

▲Up To Search▲

Price & Availability of TB6612FNG

	To Download TB6612FNG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .